DTC P2507:00 [PCM (SKYACTIV-D 2.2)]

id0102j5709800

DTC P2507:00

PCM battery voltage low input

DETECTION CONDITION

•  When the following conditions are met, a condition in which the backup power voltage is less than 50% of the battery voltage continues for 10 s.

MONITORING CONDITIONS

―  Battery voltage: 10—16 V

―  0.5 s have elapsed after the ignition was switched ON (engine off or on)

Diagnostic support note

•  This is a continuous monitor (CCM).

•  The check engine light illuminates if the PCM detects the above malfunction condition during the first drive cycle.

•  FREEZE FRAME DATA/Snapshot data is available.

•  DTC is stored in the PCM memory.

FAIL-SAFE FUNCTION

•  Inhibits engine-stop by operating the i-stop function.

POSSIBLE CAUSE

•  Battery malfunction

•  Short to ground or open circuit in backup voltage circuit

―  Short to ground in wiring harness between MAIN 200 A fuse and PCM terminal 2O

―  MAIN 200 A fuse and/or ENG.+B 7.5 A fuse malfunction

―  Open circuit in wiring harness between battery positive terminal and PCM terminal 2O

•  PCM connector or terminals malfunction

•  PCM malfunction

DTC P2507:00	PCM battery voltage low input
DETECTION CONDITION	• When the following conditions are met, a condition in which the backup power voltage is less than 50% of the battery voltage continues for 10 s. MONITORING CONDITIONS ― Battery voltage: 10—16 V ― 0.5 s have elapsed after the ignition was switched ON (engine off or on) Diagnostic support note • This is a continuous monitor (CCM). • The check engine light illuminates if the PCM detects the above malfunction condition during the first drive cycle. • FREEZE FRAME DATA/Snapshot data is available. • DTC is stored in the PCM memory.
FAIL-SAFE FUNCTION	• Inhibits engine-stop by operating the i-stop function.
POSSIBLE CAUSE	• Battery malfunction • Short to ground or open circuit in backup voltage circuit ― Short to ground in wiring harness between MAIN 200 A fuse and PCM terminal 2O ― MAIN 200 A fuse and/or ENG.+B 7.5 A fuse malfunction ― Open circuit in wiring harness between battery positive terminal and PCM terminal 2O • PCM connector or terminals malfunction • PCM malfunction

Diagnostic Procedure

STEP	INSPECTION		ACTION
1	VERIFY FREEZE FRAME DATA/SNAPSHOT DATA HAS BEEN RECORDED • Has the FREEZE FRAME DATA/snapshot data been recorded?	Yes	Go to the next step.
1		No	Record the FREEZE FRAME DATA/snapshot data on the repair order, then go to the next step.
2	VERIFY RELATED SERVICE INFORMATION AVAILABILITY • Verify related Service Information availability. • Is any related Service Information available?	Yes	Perform repair or diagnosis according to the available Service Information. • If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	INSPECT BATTERY • Switch the ignition to off. • Inspect the battery. (See BATTERY INSPECTION [SKYACTIV-D 2.2].) • Is there any malfunction?	Yes	Recharge or replace the battery, then go to Step 6. (See BATTERY RECHARGING [SKYACTIV-D 2.2].) (See BATTERY REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)
3		No	Go to the next step.
4	INSPECT BACKUP VOLTAGE CIRCUIT FOR SHORT TO GROUND OR OPEN CIRCUIT • Reconnect all disconnected connectors. • Access the VPWR PID using the M-MDS. (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-D 2.2)].) • Verify the VPWR PID value. • Is the VPWR PID value B+?	Yes	Go to the next step.
4		No	Inspect the MAIN 200 A fuse and ENG.+B 7.5 A fuse. • If the fuse is burnt out: ― Refer to the wiring diagram and verify whether or not there is a common connector between MAIN 200 A fuse and PCM terminal 2O. If there is a common connector: • Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground. • Repair or replace the malfunctioning part. If there is no common connector: • Repair or replace the wiring harness which has a short to ground. • Replace the malfunctioning fuse. • If the fuse is damaged: ― Replace the malfunctioning fuse. • If all fuses are normal: ― Refer to the wiring diagram and verify whether or not there is a common connector between battery positive terminal and PCM terminal 2O. If there is a common connector: • Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit. • Repair or replace the malfunctioning part. If there is no common connector: • Repair or replace the wiring harness which has an open circuit. Go to Step 6.
5	INSPECT PCM CONNECTOR CONDITION • Switch the ignition to off. • Disconnect the PCM connector. • Inspect for poor connection (such as damaged/pulled-out pins, corrosion). • Is there any malfunction?	Yes	Repair or replace the connector and/or terminals, then go to the next step.
5		No	Go to the next step.
6	VERIFY DTC TROUBLESHOOTING COMPLETED • Always reconnect all disconnected connectors. • Clear the DTC from the PCM memory using the M-MDS. (See AFTER REPAIR PROCEDURE [PCM (SKYACTIV-D 2.2)].) • Perform the DTC Reading Procedure. (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-D 2.2)].) • Is the same DTC present?	Yes	Repeat the inspection from Step 1. • If the malfunction recurs, replace the PCM. (See PCM REMOVAL/INSTALLATION [SKYACTIV-D 2.2].) Go to the next step.
6		No	Go to the next step.
7	VERIFY AFTER REPAIR PROCEDURE • Perform the “AFTER REPAIR PROCEDURE”. (See AFTER REPAIR PROCEDURE [PCM (SKYACTIV-D 2.2)].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [PCM (SKYACTIV-D 2.2)].)
7		No	DTC troubleshooting completed.