DTC C2005:01 [ELECTRIC PARKING BRAKE]

id040257251200

Description

Electric parking brake motor gear unit (RH) circuit malfunction

Detection condition

•  Electric parking brake control module detects an electric parking motor gear unit (RH) circuit malfunction.

Fail-safe

Not applicable

Possible cause

•  Electric parking brake motor gear unit (RH) connector or terminal malfunction

•  Electric parking brake control module connector or terminal malfunction

•  Short to ground in wiring harness between the following terminals:

―  Electric parking brake motor gear unit (RH) terminal A—Electric parking brake control module terminal G

―  Electric parking brake motor gear unit (RH) terminal B—Electric parking brake control module terminal H

•  Short to power supply in wiring harness between the following terminals:

―  Electric parking brake motor gear unit (RH) terminal A—Electric parking brake control module terminal G

―  Electric parking brake motor gear unit (RH) terminal B—Electric parking brake control module terminal H

•  Short circuit between electric parking brake motor gear unit (RH) circuits

•  Electric parking brake motor gear unit (RH) malfunction

•  Electric parking brake control module malfunction

Description	Electric parking brake motor gear unit (RH) circuit malfunction
Detection condition	• Electric parking brake control module detects an electric parking motor gear unit (RH) circuit malfunction.
Fail-safe	Not applicable
Possible cause	• Electric parking brake motor gear unit (RH) connector or terminal malfunction • Electric parking brake control module connector or terminal malfunction • Short to ground in wiring harness between the following terminals: ― Electric parking brake motor gear unit (RH) terminal A—Electric parking brake control module terminal G ― Electric parking brake motor gear unit (RH) terminal B—Electric parking brake control module terminal H • Short to power supply in wiring harness between the following terminals: ― Electric parking brake motor gear unit (RH) terminal A—Electric parking brake control module terminal G ― Electric parking brake motor gear unit (RH) terminal B—Electric parking brake control module terminal H • Short circuit between electric parking brake motor gear unit (RH) circuits • Electric parking brake motor gear unit (RH) malfunction • Electric parking brake control module malfunction

Diagnostic Procedure

Step	Inspection		Action
1	INSPECT ELECTRIC PARKING BRAKE MOTOR GEAR UNIT (RH) CONNECTOR CONDITION • Switch the ignition off. • Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT i-stop)].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].) • Disconnect the electric parking brake motor gear unit (RH) connector. • Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection. • Is the connector normal?	Yes	Go to the next step.
1		No	Repair or replace the connector, then go to Step 7.
2	INSPECT ELECTRIC PARKING BRAKE CONTROL MODULE CONNECTOR CONDITION • Disconnect the electric parking brake control module connector. • Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection. • Is the connector normal?	Yes	Go to the next step.
2		No	Repair or replace the connector, then go to Step 7.
3	INSPECT ELECTRIC PARKING BRAKE MOTOR GEAR UNIT (RH) CIRCUIT FOR SHORT TO GROUND • Verify that the electric parking brake motor gear unit (RH) and electric parking brake control module connectors are disconnected. • Inspect for continuity between the following terminals (wiring harness-side) and body ground: ― Electric parking brake motor gear unit (RH) terminal A ― Electric parking brake motor gear unit (RH) terminal B • Is there continuity?	Yes	Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals: • Electric parking brake motor gear unit (RH) terminal A—Electric parking brake control module terminal G • Electric parking brake motor gear unit (RH) terminal B—Electric parking brake control module terminal H If there is a common connector: • Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground. • Repair or replace the malfunctioning part. If there is no common connector: • Repair or replace the wiring harness which has a short to ground. Go to Step 7.
3		No	Go to the next step.
4	INSPECT ELECTRIC PARKING BRAKE MOTOR GEAR UNIT (RH) CIRCUIT FOR SHORT TO POWER SUPPLY • Verify that the electric parking brake motor gear unit (RH) and electric parking brake control module connectors are disconnected. • Connect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT i-stop)].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].) • Switch the ignition ON (engine off or on). • Measure the voltage at the following terminals (wiring harness-side): ― Electric parking brake motor gear unit (RH) terminal A ― Electric parking brake motor gear unit (RH) terminal B • Is the voltage 0 V?	Yes	Go to the next step.
4		No	Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals: • Electric parking brake motor gear unit (RH) terminal A—Electric parking brake control module terminal G • Electric parking brake motor gear unit (RH) terminal B—Electric parking brake control module terminal H If there is a common connector: • Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to power supply. • Repair or replace the malfunctioning part. If there is no common connector: • Repair or replace the wiring harness which has a short to power supply. Go to Step 7.
5	INSPECT ELECTRIC PARKING BRAKE MOTOR GEAR UNIT (RH) CIRCUITS FOR SHORT CIRCUIT • Switch the ignition off. • Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT i-stop)].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].) • Verify that the electric parking brake motor gear unit (RH) and electric parking brake control module connectors are disconnected. • Inspect for continuity between electric parking brake motor gear unit (RH) terminals A and B (wiring harness-side). • Is there continuity?	Yes	Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals: • Electric parking brake motor gear unit (RH) terminal A—Electric parking brake control module terminal G • Electric parking brake motor gear unit (RH) terminal B—Electric parking brake control module terminal H If there is a common connector: • Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to each other. • Repair or replace the malfunctioning part. If there is no common connector: • Repair or replace the wiring harness which has a short to each other. Go to Step 7.
5		No	Go to the next step.
6	VERIFY IF MALFUNCTIONING LOCATION IS ELECTRIC PARKING BRAKE MOTOR GEAR UNIT (RH) DEPENDING ON REPEATABILITY • Always reconnect all disconnected connectors. • Connect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT i-stop)].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].) • Clear the DTC for the electric parking brake control module using the M-MDS. (See CLEARING DTC [ELECTRIC PARKING BRAKE].) • Perform the following procedure 3 times or more. ― Pull up the electric parking brake switch to operate the electric parking brake. ― Press down the electric parking brake switch to release the electric parking brake. • Retrieve the electric parking brake control module DTCs using the M-MDS. (See DTC INSPECTION [ELECTRIC PARKING BRAKE].) • Is the same DTC displayed?	Yes	Replace the electric parking brake motor gear unit (RH), then go to the next step. (See ELECTRIC PARKING BRAKE MOTOR GEAR UNIT REMOVAL/INSTALLATION.)
6		No	Go to Step 8.
7	VERIFY THAT REPAIRS HAVE BEEN COMPLETED • Always reconnect all disconnected connectors. • Connect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT i-stop)].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].) • Clear the DTC for the electric parking brake control module using the M-MDS. (See CLEARING DTC [ELECTRIC PARKING BRAKE].) • Perform the following procedure 3 times or more. ― Pull up the electric parking brake switch to operate the electric parking brake. ― Press down the electric parking brake switch to release the electric parking brake. • Retrieve the electric parking brake control module DTCs using the M-MDS. (See DTC INSPECTION [ELECTRIC PARKING BRAKE].) • Is the same DTC displayed?	Yes	Repeat the inspection from Step 1. • If the malfunction recurs, replace the electric parking brake control module. (See ELECTRIC PARKING BRAKE CONTROL MODULE REMOVAL/INSTALLATION.) Go to the next step.
7		No	Go to the next step.
8	VERIFY IF OTHER DTCs DISPLAYED • Are any other DTCs displayed?	Yes	Repair or replace the malfunctioning part according to the applicable DTC troubleshooting. (See DTC TABLE [ELECTRIC PARKING BRAKE].)
8		No	DTC troubleshooting completed.