HEADLIGHT BULB REMOVAL/INSTALLATION

id091800800500

Headlight (Bulb Type)

Headlight LO bulb (LH) (SKYACTIV-G 2.0, SKYACTIV-G 2.5)

1.  Turn the steering wheel to full right lock.

2.  Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT i-stop)].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5].)

3.  Partially peel back the mudguard (LH). (See MUDGUARD REMOVAL/INSTALLATION.)

4.  Disconnect the connector.

am6zzw00008030

5.  Rotate the headlight LO bulb in the direction of the arrow (1) shown in the figure to remove it in the direction of the arrow (2) shown in the figure.

am6zzw00011256

Caution

•  If there is oil or dirt on the surface of the light bulb, excessive heat will build up and the life of the light bulb will be shortened. If the light bulb glass area is touched, wipe off any dirt using a soft cloth dampened with detergent diluted in water (approx. 5 %).

6.  Install in the reverse order of removal.

Headlight LO bulb (LH) (SKYACTIV-D 2.2)

1.  Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].)

2.  Remove the air cleaner cover. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)

3.  Remove the nut and bolt.

am6zzw00012759

4.  Insert a tape-wrapped flathead screwdriver into the service hole in the position shown in the figure.

am6zzw00009215

5.  While pressing the clip tab of the relay and fuse block in the direction of the arrow (1) shown in the figure, pull the clip of the relay and fuse block in the direction of the arrow (2) to detach the clip tab of the relay and fuse block from the engine mount.

am6zzw00009216

6.  Pull out the relay and fuse block from the stud bolt and set it aside as shown in the figure.

am6zzw00009217

7.  Disconnect the connector.

am6zzw00008030

8.  Rotate the headlight LO bulb in the direction of the arrow (1) shown in the figure to remove it in the direction of the arrow (2) shown in the figure.

am6zzw00012760

Caution

•  If there is oil or dirt on the surface of the light bulb, excessive heat will build up and the life of the light bulb will be shortened. If the light bulb glass area is touched, wipe off any dirt using a soft cloth dampened with detergent diluted in water (approx. 5 %).

9.  Install in the reverse order of removal.

Headlight LO bulb (RH) (SKYACTIV-G 2.0, SKYACTIV-G 2.5)

1.  Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT i-stop)].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5].)

2.  Disconnect the connector.

am6zzw00009218

3.  Rotate the headlight LO bulb in the direction of the arrow (1) shown in the figure to remove it in the direction of the arrow (2) shown in the figure.

am6zzw00009219

Caution

•  If there is oil or dirt on the surface of the light bulb, excessive heat will build up and the life of the light bulb will be shortened. If the light bulb glass area is touched, wipe off any dirt using a soft cloth dampened with detergent diluted in water (approx. 5 %).

4.  Install in the reverse order of removal.

Headlight LO bulb (RH) (SKYACTIV-D 2.2)

1.  Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].)

2.  Remove the washer tank bracket. (See WASHER TANK REMOVAL/INSTALLATION.)

3.  Disconnect the connector.

am6zzw00009218

4.  Rotate the headlight LO bulb in the direction of the arrow (1) shown in the figure to remove it in the direction of the arrow (2) shown in the figure.

am6zzw00009219

Caution

•  If there is oil or dirt on the surface of the light bulb, excessive heat will build up and the life of the light bulb will be shortened. If the light bulb glass area is touched, wipe off any dirt using a soft cloth dampened with detergent diluted in water (approx. 5 %).

5.  Install in the reverse order of removal.

Headlight HI bulb (Without running light system)

1.  Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT i-stop)].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].)

2.  Remove the air cleaner cover. (Headlight HI bulb (LH)) (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)

3.  Remove the washer tank bracket. (Headlight HI bulb (RH)) (See WASHER TANK REMOVAL/INSTALLATION.)

4.  Disconnect the connector.

am6zzw00008278

5.  Rotate the headlight HI bulb in the direction of the arrow (1) shown in the figure and remove it in the direction of the arrow (2) shown in the figure.

am6zzw00008279

Caution

•  If there is oil or dirt on the surface of the light bulb, excessive heat will build up and the life of the light bulb will be shortened. If the light bulb glass area is touched, wipe off any dirt using a soft cloth dampened with detergent diluted in water (approx. 5 %).

6.  Install in the reverse order of removal.

Headlight HI bulb (With running light system)

1.  Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT i-stop)].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].)

2.  Remove the air cleaner cover. (Headlight HI bulb (LH)) (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)

3.  Remove the washer tank bracket. (Headlight HI bulb (RH)) (See WASHER TANK REMOVAL/INSTALLATION.)

4.  Rotate the cover in the direction of the arrow (1) shown in the figure and remove it in the direction of the arrow (2) shown in the figure.

am6zzw00009220

5.  Rotate the headlight HI bulb in the direction of the arrow (1) shown in the figure to disconnect the connector.

am6zzw00012761

6.  Remove the headlight HI bulb.

Caution

•  If there is oil or dirt on the surface of the light bulb, excessive heat will build up and the life of the light bulb will be shortened. If the light bulb glass area is touched, wipe off any dirt using a soft cloth dampened with detergent diluted in water (approx. 5 %).

7.  Install in the reverse order of removal.

Headlight (LED Type)

Note

•  The LED-type headlight is integrated with the front combination light.

•  When replacing the LED-type headlight, replace the front combination light. (See FRONT COMBINATION LIGHT REMOVAL/INSTALLATION.)