DTC B1206:00/B143A:00/B1A55:00/U2107:00 [SAS CONTROL MODULE]

id0802g6015000

System malfunction location

•  B1206:00:SAS control module collision judgement signal output (fuel cut signal output)

•  B143A:00:SAS control module collision judgement signal output (collision detection signal output)

•  B1A55:00:SAS control module collision judgement signal output (collision detection signal for MAZDA ERA-GLONASS output)

•  U2107:00:SAS control module collision judgement signal output (ESS request signal output)

Detection condition

Warning

•  Detection conditions are for understanding the DTC outline before performing an inspection. Performing an inspection according to only the detection conditions may cause injury due to an operating error, or damage the system. When performing an inspection, always follow the inspection procedure.

•  SAS control module outputs collision judgement signal

Fail-safe

Not applicable

Possible cause

•  SAS control module operation (deployment)

•  SAS control module outputs collision judgement signal

•  SAS control module malfunction

System wiring diagram

Not applicable

System malfunction location	• B1206:00:SAS control module collision judgement signal output (fuel cut signal output) • B143A:00:SAS control module collision judgement signal output (collision detection signal output) • B1A55:00:SAS control module collision judgement signal output (collision detection signal for MAZDA ERA-GLONASS output) • U2107:00:SAS control module collision judgement signal output (ESS request signal output)
Detection condition	Warning • Detection conditions are for understanding the DTC outline before performing an inspection. Performing an inspection according to only the detection conditions may cause injury due to an operating error, or damage the system. When performing an inspection, always follow the inspection procedure. • SAS control module outputs collision judgement signal
Fail-safe	Not applicable
Possible cause	• SAS control module operation (deployment) • SAS control module outputs collision judgement signal • SAS control module malfunction
System wiring diagram	Not applicable

Diagnostic Procedure

Step

Inspection

Action

1

PERFORM SAS CONTROL MODULE DTC INSPECTION

•  Clear the DTC for the SAS control module using the M-MDS. (See CLEARING DTC [SAS CONTROL MODULE].)

•  Perform the DTC inspection for the SAS control module using the M-MDS. (See DTC INSPECTION [SAS CONTROL MODULE].)

•  Is the DTC B1193:00 displayed?

Yes

Replace the SAS control module. (See SAS CONTROL MODULE REMOVAL/INSTALLATION.)

No

Go to the next step.

2

VERIFY THAT REPAIRS HAVE BEEN COMPLETED

•  Clear the DTC for the SAS control module using the M-MDS.
(See CLEARING DTC [SAS CONTROL MODULE].)

•  Perform the DTC inspection for the SAS control module using the M-MDS.
(See DTC INSPECTION [SAS CONTROL MODULE].)

•  Are the same DTCs displayed?

Yes

Repeat the inspection from Step 1.

•  If the malfunction recurs, replace the SAS control module, then go to the next step.
(See SAS CONTROL MODULE REMOVAL/INSTALLATION.)

No

Go to the next step.

3

VERIFY IF OTHER DTCs DISPLAYED

•  Are any other DTCs displayed?

Yes

Repair the malfunctioning part according to the applicable DTC troubleshooting.(See DTC TABLE [SAS CONTROL MODULE].)

No

DTC troubleshooting completed.

Step	Inspection		Action
1	PERFORM SAS CONTROL MODULE DTC INSPECTION • Clear the DTC for the SAS control module using the M-MDS. (See CLEARING DTC [SAS CONTROL MODULE].) • Perform the DTC inspection for the SAS control module using the M-MDS. (See DTC INSPECTION [SAS CONTROL MODULE].) • Is the DTC B1193:00 displayed?	Yes	Replace the SAS control module. (See SAS CONTROL MODULE REMOVAL/INSTALLATION.)
1		No	Go to the next step.
2	VERIFY THAT REPAIRS HAVE BEEN COMPLETED • Clear the DTC for the SAS control module using the M-MDS. (See CLEARING DTC [SAS CONTROL MODULE].) • Perform the DTC inspection for the SAS control module using the M-MDS. (See DTC INSPECTION [SAS CONTROL MODULE].) • Are the same DTCs displayed?	Yes	Repeat the inspection from Step 1. • If the malfunction recurs, replace the SAS control module, then go to the next step. (See SAS CONTROL MODULE REMOVAL/INSTALLATION.)
2		No	Go to the next step.
3	VERIFY IF OTHER DTCs DISPLAYED • Are any other DTCs displayed?	Yes	Repair the malfunctioning part according to the applicable DTC troubleshooting.(See DTC TABLE [SAS CONTROL MODULE].)
3		No	DTC troubleshooting completed.