DTC B116A:12 [MAZDA ERA-GLONASS CONTROL MODULE]

id0902r6059100

Description

Microphone circuit malfunction
Detection condition
The Mazda ERA-GLONASS control module detected a short to power supply in the microphone circuit for 1 second with the ignition switched ON (engine off or on).
Fail-safe function
Not applicable
Possible cause
•  Microphone connector or terminal malfunction
•  Mazda ERA-GLONASS control module connector or terminal malfunction
•  Short to power supply in wiring harness between the following terminals:
―  Mazda ERA-GLONASS control module terminal 1E and microphone terminal C
•  Microphone malfunction
•  Mazda ERA-GLONASS control module malfunction

Diagnostic Procedure

Step

Inspection

Action
1
INSPECT MICROPHONE CONNECTOR CONDITION
•  Switch the ignition off.
•  Disconnect the negative battery cable.
•  Disconnect the microphone connector.
•  Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
•  Is the connector normal?
Yes
Go to the next step.
No
Repair or replace the connector, then go to Step 5.
2
INSPECT MAZDA ERA-GLONASS CONTROL MODULE CONNECTOR CONDITION
•  Disconnect the Mazda ERA-GLONASS control module connector.
•  Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
•  Is the connector normal?
Yes
Go to the next step.
No
Repair or replace the connector, then go to Step 5.
3
INSPECT MICROPHONE CIRCUIT FOR SHORT TO POWER SUPPLY
•  Verify that the microphone and Mazda ERA-GLONASS control module connectors are disconnected.
•  Connect the negative battery cable.
•  Switch the ignition ON (engine off or on)
•  Measure the voltage at the following terminal (wiring harness-side):
―  Mazda ERA-GLONASS control module terminal 1E
•  Is the voltage 0 V?
Yes
Go to the next step.
No
Refer to the wiring diagram and verify if there is a common connector between the following terminals.
•  Mazda ERA-GLONASS control module terminal 1E and microphone terminal C
If there is a common connector:
•  Inspect the common connector and terminals for corrosion, damage, or disconnection and the common wiring harnesses for short to power supply to determine the malfunctioning location.
•  Repair or replace the malfunctioning location.
If there is no common connector:
•  Repair or replace the wiring harness which is shorted to power supply.
Go to Step 5.
4
PERFORM DTC INSPECTION AND VERIFY IF MALFUNCTIONING LOCATION IS MICROPHONE
•  Switch the ignition off.
•  Disconnect the negative battery cable.
•  Always reconnect all disconnected connectors.
•  Reconnect the negative battery cable.
•  Clear the DTC for the Mazda ERA-GLONASS control module using the M-MDS.
•  Switch the ignition ON (engine off or on) and wait for 25 s or more.
•  Perform the DTC inspection for the Mazda ERA-GLONASS control module using the M-MDS.
•  Is the same DTC displayed?
Yes
Replace the microphone, then go to the next step.
(See MICROPHONE REMOVAL/INSTALLATION.)
No
Go to the next step.
5
VERIFY THAT REPAIRS HAVE BEEN COMPLETED
•  Clear the DTC for the Mazda ERA-GLONASS control module using the M-MDS.
•  Switch the ignition ON (engine off or on) and wait for 25 s or more.
•  Perform the DTC inspection for the Mazda ERA-GLONASS control module using the M-MDS.
•  Is the same DTC displayed?
Yes
Repeat the inspection from Step 1.
•  If the malfunction recurs, replace the Mazda ERA-GLONASS control module.
Go to the next step.
No
Go to the next step.
6
VERIFY IF OTHER DTCs DISPLAYED
•  Are any other DTCs displayed?
Yes
Repair the malfunctioning location according to the applicable DTC troubleshooting.
(See DTC TABLE [MAZDA ERA-GLONASS CONTROL MODULE])
No
DTC troubleshooting completed.