LOWER PANEL REMOVAL/INSTALLATION

id091700801100

Driver-side

1. Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT i-stop)].)

2. Remove the following parts:

(1) Upper panel (See UPPER PANEL REMOVAL/INSTALLATION.)

(2) Rear console (See REAR CONSOLE REMOVAL/INSTALLATION.)

(3) Console side panel (See CONSOLE SIDE PANEL REMOVAL/INSTALLATION.)

(4) Selector lever knob (ATX) (See AUTOMATIC TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION.)

(5) Shift lever knob (MTX) (See MANUAL TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION [C66M-R].) (See MANUAL TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION [D66M-R, D66MX-R].)

(6) Shift panel (See SHIFT PANEL REMOVAL/INSTALLATION.)

(7) Front console box (See FRONT CONSOLE BOX REMOVAL/INSTALLATION.)

(8) CD player (with CD player) (See CD PLAYER REMOVAL.) (See CD PLAYER INSTALLATION.)

(9) DVD/CD player (with DVD/CD player) (See DVD/CD PLAYER REMOVAL.) (See DVD/CD PLAYER INSTALLATION.)

(10) Side wall (See SIDE WALL REMOVAL/INSTALLATION.)

(11) Front console (See FRONT CONSOLE REMOVAL/INSTALLATION.)

(12) Driver-side front scuff plate (See FRONT SCUFF PLATE REMOVAL/INSTALLATION.)

(13) Driver-side front side trim (See FRONT SIDE TRIM REMOVAL/INSTALLATION.)

(14) Bonnet release lever (See BONNET LATCH AND RELEASE LEVER REMOVAL/INSTALLATION.)

(15) Fuel-filler lid opener lever (See FUEL-FILLER LID OPENER AND LEVER REMOVAL/INSTALLATION.)

3. Remove bolt.

am6xuw00007506

4. Move the driver-side lower panel in the order of arrows (1), (2), (3), (4) and (5) shown in the figure, and detach hook, clips, tabs, and guide.

am6zzw00014531

5. Disconnect the trunk lid opener switch connector. (with trunk lid opener switch)

6. Install in the reverse order of removal.

Passenger-side

Removal

2. Remove the following parts:

(1) Passenger-side front scuff plate (See FRONT SCUFF PLATE REMOVAL/INSTALLATION.)

(2) Passenger-side front side trim (See FRONT SIDE TRIM REMOVAL/INSTALLATION.)

(3) Glove compartment (See GLOVE COMPARTMENT REMOVAL/INSTALLATION.)

(4) Dashboard under cover (See DASHBOARD UNDER COVER REMOVAL/INSTALLATION.)

3. Remove bolts.

am6xuw00007508

4. Move the passenger-side lower panel in the order of arrows (1), (2), (3), and (4) shown in the figure, and detach the clips, hook, tabs, and guide from the dashboard.

am6zzw00013341

Installation

1. Move the passenger-side lower panel in the order of arrows (1), (2), (3), (4), and (5) shown in the figure, and attach the clips, hook, tabs, and guide to the dashboard.

am6zzw00013342

2. Assemble the passenger-side lower panel to the dashboard and tighten the bolts temporarily.

am6xuw00007511

3. Install the glove compartment. (See GLOVE COMPARTMENT REMOVAL/INSTALLATION.)

4. Measure the gaps between the glove compartment and the passenger-side lower panel and verify that the measured value is within the standard value.

• If not within the standard value, move the passenger-side lower panel and adjust the installation position.

am6xuw00007512

5. Remove the glove compartment. (See GLOVE COMPARTMENT REMOVAL/INSTALLATION.)

6. Tighten the bolts completely.

am6xuw00007513

7. Install the following parts:

(1) Dashboard under cover (See DASHBOARD UNDER COVER REMOVAL/INSTALLATION.)

(2) Glove compartment (See GLOVE COMPARTMENT REMOVAL/INSTALLATION.)

(3) Passenger-side front side trim (See FRONT SIDE TRIM REMOVAL/INSTALLATION.)

(4) Passenger-side front scuff plate (See FRONT SCUFF PLATE REMOVAL/INSTALLATION.)

Disassembly/Assembly (Driver-side only)

1. Disassemble in the order indicated in the table.

am6xuw00007582

1

Pocket lid

2

Coin box

3

Lower panel

2. Assemble in the reverse order of disassembly.