PID/DATA MONITOR INSPECTION (i-stop) [SKYACTIV-G 2.0, SKYACTIV-G 2.5]

id1102a4000100

Note
•  PIDs related to i-stop can be displayed in a list using the M-MDS data monitor diagnostic function.
•  If the engine is stopped by the i-stop control while the following data monitor items on the M-MDS are being viewed, the data monitor items may no longer be displayed.
―  BRAKE_SW
―  LON_ACCL_C
―  WSPD_SEN_LF
―  WSPD_SEN_RF
―  WSPD_SEN_LR
―  WSPD_SEN_RR

1.  Connect the M-MDS to the DLC-2.

2.  After vehicle identification is completed, select the following from the M-MDS initial screen.

(1)  [Data logger]
(2)  [Powertrain]
(3)  [i-stop]

3.  Select the applicable item from the PID/DATA Monitor Table.

4.  Verify the monitored value according to the directions on the screen.

PID/DATA Monitor Table

Module
Item (definition)
Unit/Condition
PCM
ALT_CUR_S
V
(See PCM INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5].)
APP
%
APP1
%
APP2
%
BARO
KPa
BATT_B_CUR
A
BATT_B_V
V
BATT_CUR
A
BATT_RES
mohm
BATT_SOC
%
BATT_TEMP
°C
BATT_V
V
BBP
KPa
BFP
KPa
BOO
High/Low
BPA
High/Low
CHG_STAT_B
%
CPP*1
%
CPP/PNP*1
Off/On
ECT
°C
IAT
°C
I-Stop_OFF
Off/On
I-Stop_TRD
Off/On
I-Stop_VSP
Off/On
I-Stop_VST
Off/On
M_GEAR*1
Neutral/1st gear/2nd gear/3rd gear/4th gear/5th gear/6th gear/Reverse/Undefined/Auto/In_Progress/YSF/Error
NEUTRAL_SW1*1
Off/On
NEUTRAL_SW2*1
Off/On
VPWR
V
DSC HU/CM
BRAKE_SW
Off/On
(See PID/DATA MONITOR TABLE [DYNAMIC STABILITY CONTROL (DSC)].)
LON_ACCL_C
G
WSPD_SEN_LF
KPH
WSPD_SEN_LR
KPH
WSPD_SEN_RF
KPH
WSPD_SEN_RR
KPH
TCM*2
I-Stop_EST
Off/On
(See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [TCM (FW6A-EL)].)
TFT
°C
TR
P/SHIFT_DOWN/SHIFT_UP/M/D/N/R
EATC
STOP_ST
Available/Not Available/Error
(See PID/DATA MONITOR TABLE [CLIMATE CONTROL UNIT (FULL-AUTO AIR CONDITIONER)].)
RCM
SEAT_B_D
Unbuckled/Buckled
(See PID/DATA MONITOR TABLE [SAS CONTROL MODULE].)
RBCM
DOOR_ALL
Close/OPEN
(See PID/DATA MONITOR TABLE [REAR BODY CONTROL MODULE (RBCM)].)
DOOR_D
Close/OPEN
HOOD
Close/OPEN
TRUNK
Close/OPEN
SSU
RELAY_ACC
Off/On
(See PID/DATA MONITOR TABLE [START STOP UNIT].)
RELAY_IG1
Off/On
RELAY_IG2
Off/On
SSB_1
Off/On
SSB_2
Off/On
VPWR_ACC
V
VPWR_B1
V
VPWR_IG1
V
EPS
STR_AB_EST
° (deg)
(See PID/DATA MONITOR TABLE [ELECTRIC POWER STEERING (EPS)].)
STR_ROT_SPD
°/s
STR_TRQ_S_M
Nm
DC-DC Converter (i-ELOOP)*3
BYPS_STAT
Bypass Off/Bypass On/Bypass Off fault/Bypass On fault
(See PID/DATA MONITOR INSPECTION [i-ELOOP].)
DCDC_IN_V
V

*1  :MTX
*2  :ATX
*3  :With i-ELOOP