PID/DATA MONITOR TABLE [DYNAMIC STABILITY CONTROL (DSC)]

id0402b2886400

PID name (definition)	Unit/Condition	Operation condition (reference)	Action
BRAKE_SW	Off/On	•  Brake pedal released: Off •  Brake pedal depressed: On	Inspect the brake switch. (See BRAKE SWITCH INSPECTION.)
BRK_F_P_R (Raw Value)	Pa, psi	•  Brake pedal depressed: Changes according to the brake fluid pressure	Inspect the brake fluid pressure sensor. (See BRAKE FLUID PRESSURE SENSOR INSPECTION.)
DDS_MODE	Not_Learned/Learning/Learned	•  During initialization: Not_Learned •  During learning: Learning •  Learning completed*: Learned	Perform the DTC inspection for the DSC HU/CM. (See DTC INSPECTION [DYNAMIC STABILITY CONTROL (DSC)].)
DSC_OFF_SW	Off/On	•  DSC OFF switch is released: Off •  DSC OFF switch is depressed: On	Inspect the DSC OFF switch. (See DSC OFF SWITCH INSPECTION.)
DSC_ST	Off/On	•  During DSC OFF mode: Off •  Other than DSC OFF mode: On	Perform the DTC inspection for the DSC HU/CM. (See DTC INSPECTION [DYNAMIC STABILITY CONTROL (DSC)].)
LAT_ACCL_R (Raw Value)	G	•  Vehicle stopped or driving at constant speed: 0 G •  Cornering to left: Changes 0 G—positive •  Cornering to right: Changes 0 G—negative	Perform the DTC inspection for the SAS control module. (See DTC INSPECTION [SAS CONTROL MODULE].)
LON_ACCL_C (Calculated Value)	G	•  Vehicle stopped or driving at constant speed: 0 G •  Vehicle is driving at a acceleration: Changes 0 G—positive •  Vehicle is driving at a deceleration: Changes 0 G—negative	Perform the DTC inspection for the SAS control module. (See DTC INSPECTION [SAS CONTROL MODULE].)
LON_ACCL_R (Raw Value)
PMP_MT_SP	Off/On	•  Pump motor not activated: Off •  Pump motor activated: On	Inspect the DSC HU/CM. (See DSC HU/CM INSPECTION.)
STR_ANG_C (Calculated Value)	°	•  Steering wheel in neutral position (not turned): 0° •  Steering wheel turned to left: Changes 0°—positive •  Steering wheel turned to right: Changes 0°—negative Note •  Constantly indicates 0° until the steering wheel angle neutral position determination by the DSC HU/CM is completed. •  The steering wheel angle neutral position determination by the DSC HU/CM is completed when the vehicle is driven in a straight line at a speed of 20 km/h or more for several seconds.	Perform the DTC inspection for the PCM, DSC HU/CM, and EPS control module. If a DTC is displayed after performing the DTC inspection for the PCM, DSC HU/CM, and EPS control module, repair the malfunctioning part according to the applicable DTC troubleshooting. (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5)].) (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-D 2.2)].) (See DTC INSPECTION [DYNAMIC STABILITY CONTROL (DSC)].) (See EPS CONTROL MODULE INSPECTION.) After performing the DTC inspection, perform the following procedures: •  Start the engine and drive the vehicle in a straight line at a speed of 20 km/h or more for several seconds. If an abnormal value is indicated after verifying the value of the STR_ANG_C again, replace the DSC HU/CM.
STR_ANG_R (Raw Value)		•  Steering wheel position when ignition is switched ON (engine off or on): 0° •  Steering wheel turned to left: Changes 0°—positive •  Steering wheel turned to right: Changes 0°—negative Note •  The signal displayed in this item is a steering angle (relative angle) signal output from the EPS control module.	Inspect the following PID. •  STR_ANG (See EPS CONTROL MODULE INSPECTION.)
TPMS_TYPE	No_DDS/DDS/DDS+TOM_O/DDS+TOM_EU/DDS+TOM_US	•  TPMS not equipped: No_DDS •  TPMS equipped: DDS •  TPMS equipped (Corresponding to European and U.S. regulations): DDS+TOM_O •  TPMS equipped (Corresponding to European regulations): DDS+TOM_EU •  TPMS equipped (Corresponding to U.S. regulations): DDS+TOM_US	Perform the DTC inspection for the DSC HU/CM. (See DTC INSPECTION [DYNAMIC STABILITY CONTROL (DSC)].)
V_INLET_LF	Off/On	•  Solenoid valve not activated: Off •  Solenoid valve activated: On	Inspect the DSC HU/CM. (See DSC HU/CM INSPECTION.)
V_INLET_LR
V_INLET_RF
V_INLET_RR
V_OUTLET_LF
V_OUTLET_LR
V_OUTLET_RF
V_OUTLET_RR
V_TRC_LF/RR	Off/On	•  Solenoid valve activated: On •  Solenoid valve not activated: Off	Inspect the DSC HU/CM. (See DSC HU/CM INSPECTION.)
V_TRC_RF/LR
VPWR_B_SOL	V	•  Ignition switched ON (engine off): Approx. 12.2 V •  Idling: Approx. 14.1 V	Inspect power supply circuit. (See DSC HU/CM INSPECTION.)
VSPD	KPH, MPH	•  Vehicle stopped: 0 KPH, 0 MPH •  Vehicle running: Vehicle speed	Inspect the DSC HU/CM. (See DSC HU/CM INSPECTION.)
WSPD_SEN_LF	KPH, MPH	•  Vehicle stopped: 0 KPH, 0 MPH •  Vehicle running: Vehicle speed	Inspect the front ABS wheel-speed sensor. (See FRONT ABS WHEEL-SPEED SENSOR INSPECTION.)
WSPD_SEN_LR			Inspect the rear ABS wheel-speed sensor. (See REAR ABS WHEEL-SPEED SENSOR INSPECTION.)
WSPD_SEN_RF			Inspect the front ABS wheel-speed sensor. (See FRONT ABS WHEEL-SPEED SENSOR INSPECTION.)
WSPD_SEN_RR			Inspect the rear ABS wheel-speed sensor. (See REAR ABS WHEEL-SPEED SENSOR INSPECTION.)
YAW_RATE_C (Calculated Value)	°/s	•  Vehicle stopped or driving straight: 0 °/s •  Cornering to left: Changes 0 °/s—positive •  Cornering to right: Changes 0 °/s—negative	Perform the DTC inspection for the SAS control module. (See DTC INSPECTION [SAS CONTROL MODULE].)
YAW_RATE_R (Raw Value)