CRUISE CONTROL SWITCH INSPECTION [MAZDA RADAR CRUISE CONTROL (MRCC) SYSTEM]

id1520000052a1

Resistance Inspection

Warning

•  Handling the driver-side air bag module improperly can accidentally operate (deploy) the air bag module, which may seriously injure you. Read the service warnings and cautions before handling the air bag module. (See AIR BAG SYSTEM SERVICE WARNINGS.) (See AIR BAG SYSTEM SERVICE CAUTIONS.)

1.  Switch the ignition off.

2.  Disconnect the negative battery cable and wait for 1 min or more. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT i-stop)].)

3.  Remove the driver-side air bag module. (See DRIVER-SIDE AIR BAG MODULE REMOVAL.) (See DRIVER-SIDE AIR BAG MODULE INSTALLATION.)

4.  Remove the steering wheel. (See STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION.)

5.  Measure the resistance between cruise control switches 3E and 3A under the following conditions:

•  Resistance with MRCC OFF switch (without adjustable speed limiter)/MRCC ON/OFF switch (with adjustable speed limiter) pressed and held

―  0 ohms

am6zzw00014050

•  Resistance with CANCEL switch pressed and held

―  83.655—85.345 ohms

am6zzw00014051

•  Resistance with SET (-) switch pressed and held

―  187.605—191.395 ohms

am6zzw00014052

•  Resistance with SET (+) switch pressed and held

―  323.235—329.765 ohms

am6zzw00014053

•  Resistance with RESUME switch pressed and held

―  501.435—511.565 ohms

am6zzw00014054

•  Resistance with MRCC ON switch (without adjustable speed limiter)/speed limiter switch (with adjustable speed limiter) pressed and held

―  753.885—769.115 ohms

am6zzw00014055

•  Resistance with DISTANCE (+) switch pressed and held

―  1,139.985—1,163.015 ohms

am6zzw00014056

•  Resistance with DISTANCE (-) switch pressed and held

―  1,753.785—1,789.215 ohms

am6zzw00014057

•  Resistance with any switches not pressed

―  3,278.385—3,344.615 ohms

am6zzw00014058

LED Illumination Inspection

Warning

•  Handling the driver-side air bag module improperly can accidentally operate (deploy) the air bag module, which may seriously injure you. Read the service warnings and cautions before handling the air bag module. (See AIR BAG SYSTEM SERVICE WARNINGS.) (See AIR BAG SYSTEM SERVICE CAUTIONS.)

1.  Switch the ignition off.

2.  Disconnect the negative battery cable and wait for 1 min or more. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT i-stop)].)

3.  Remove the driver-side air bag module. (See DRIVER-SIDE AIR BAG MODULE REMOVAL.) (See DRIVER-SIDE AIR BAG MODULE INSTALLATION.)

4.  Remove the steering wheel. (See STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION.)

5.  Apply battery positive voltage to cruise control switch terminal 3F, and connect terminal 3B to ground.

am6zzw00014059

6.  Verify that the LED illuminates.

•  If the LED does not illuminate, replace the cruise control switch.