PARKING SENSOR SYSTEM DOES NOT OPERATE [PARKING SENSOR SYSTEM]

id0903n7200300

Note
•  If there is any vehicle malfunction complaint lodged by a customer, perform FOREWORD [PARKING SENSOR SYSTEM] malfunction diagnosis according to the troubleshooting procedure. (See FOREWORD [PARKING SENSOR SYSTEM].)

Description

•  Even if the parking sensor switch is turned on, the parking sensor buzzer is not activated or the parking sensor indicator is not turned on.

Possible Causes

•  Cluster switch connector or terminal malfunction
•  Parking assist unit connector or terminal malfunction
•  Short to ground in wiring harness between the following terminals:
―  Cluster switch terminal A—Parking assist unit terminal V
•  Open circuit in wiring harness between the following terminals:
―  Cluster switch terminal A—Parking assist unit terminal V
―  Cluster switch terminal C—Body ground
•  Cluster switch malfunction
•  Parking assist unit malfunction

System Wiring Diagram

am6zzw00014948

Diagnostic Procedure

Step

Inspection

Action
1
VERIFY ALL SYSTEM DTCs
•  Switch the ignition off.
•  Switch the ignition ON (engine off or on) and wait for 10 s or more.
•  Perform a CMDTC self-test using the M-MDS.
•  Are any DTCs displayed?
Yes
Repair or replace the malfunctioning part according to the applicable DTC troubleshooting.
(See DTC TABLE [PARKING ASSIST UNIT].)
No
Go to the next step.
2
VERIFY MALFUNCTION SYMPTOM
•  Switch the ignition ON (engine off or on).
•  Turn the parking sensor switch on.
•  Does the parking sensor indicator turn on and is the buzzer activated?
Yes
If buzzer is activated after turning the indicator on:
•  System is normal.
If buzzer is not activated:
•  Perform an inspection referring to "PARKING SENSOR BUZZER DOES NOT ACTIVATE/BUZZER SOUND IS SMALL".
If indicator does not turn on:
•  Inspect the parking sensor switch.
No
Go to the next step.
3
INSPECT CLUSTER SWITCH CONNECTOR CONDITION
•  Switch the ignition off.
•  Disconnect the negative battery cable.
•  Disconnect the cluster switch connector.
•  Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
•  Is the connector normal?
Yes
Go to the next step.
No
Repair or replace the connector.
4
INSPECT PARKING ASSIST UNIT CONNECTOR CONDITION
•  Disconnect the parking assist unit connector.
•  Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
•  Is the connector normal?
Yes
Go to the next step.
No
Repair or replace the connector.
5
INSPECT PARKING SENSOR SWITCH CIRCUIT FOR SHORT TO GROUND
•  Verify that the cluster switch and parking assist unit connectors are disconnected.
•  Inspect for continuity between the following terminals (wiring harness-side) and body ground:
―  Cluster switch terminal A
•  Is there continuity?
Yes
Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:
•  Cluster switch terminal A—Parking assist unit terminal V
If there is a common connector:
•  Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground.
•  Repair or replace the malfunctioning part.
If there is no common connector:
•  Repair or replace the wiring harness which has a short to ground.
No
Go to the next step.
6
INSPECT PARKING SENSOR SWITCH CIRCUIT FOR OPEN CIRCUIT
•  Switch the ignition off.
•  Disconnect the negative battery cable.
•  Verify that the cluster switch and parking assist unit connectors are disconnected.
•  Inspect for continuity between the following terminals (wiring harness-side):
―  Cluster switch terminal A—Parking assist unit terminal V
―  Cluster switch terminal C—Body ground
•  Is there continuity?
Yes
Go to the next step.
No
Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:
•  Cluster switch terminal A—Parking assist unit terminal V
•  Cluster switch terminal C—Body ground
If there is a common connector:
•  Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit.
•  Repair or replace the malfunctioning part.
If there is no common connector:
•  Repair or replace the wiring harness which has an open circuit.
7
INSPECT PARKING SENSOR SWITCH
•  Inspect the parking sensor switch.
•  Is the parking sensor switch normal?
Yes
Replace the parking assist unit.
(See PARKING ASSIST UNIT REMOVAL/INSTALLATION.)
No
Replace the cluster switch.
(See CLUSTER SWITCH REMOVAL/INSTALLATION.)