i-stop WARNING LIGHT (AMBER) [SKYACTIV-D 2.2]

id0140z7008700

Purpose, Function

• If the i-stop control inhibits the operation, the i-stop warning light (amber) flashes/illuminates to inform the driver that the i-stop control inhibits the operation.

Construction

• The i-stop warning light (amber) is built into the instrument cluster.

• For vehicles with center display, a warning message in the center display is displayed when the i-stop warning light (amber) is illuminated or flashes. For the message content and verification method, refer to the [Center Display]. (See CENTER DISPLAY [WITH CENTER DISPLAY].)

Operation

• The flashing/illumination conditions of the i-stop warning light (amber) are as follows:

i-stop warning light (amber) flashing condition

― Any of the following DTCs are stored:

PCM DTC

• P0555:00, P057F:00, P058A:00, P0615:00, P0A0F:00, P0A8D:00, P0A94:00, P2502:00, P2503:00, P2504:00, U0101:00, U0121:00, U0131:00, U0140:00, U0151:00, U0155:00, U0214:00, U0298:00

• For details on DTCs, refer to [Engine On-board Diagnostic System Malfunction Detection Function]. (See ON-BOARD DIAGNOSTIC SYSTEM TEST MODE [PCM (SKYACTIV-D 2.2)].)

TCM DTC

• P0C2C:00, P181F:00, P2712:00

• For details on DTCs, refer to [Transmission/Transaxle On-board Diagnostic System Malfunction Detection Function]. (See ON-BOARD DIAGNOSTIC SYSTEM MALFUNCTION DETECTION FUNCTION [TCM (GW6A-EL, GW6AX-EL)].)

DSC HU/CM DTC

• C0001:01, C0002:01, C0003:01, C0004:01, C0010:01, C0011:01, C0014:01, C0015:01, C0018:01, C0019:01, C001C:01, C001D:01, C0020:01, C0020:1C, C0020:71, C0030:07, C0031:01, C0031:07, C0033:07, C0034:01, C0034:07, C0036:07, C0037:01, C0037:07, C0039:07, C003A:01, C003A:07, C0044:01, C0044:28, C0044:54, C0044:64, C0051:28, C0061:28, C0061:54, C0061:64, C0062:28, C0062:54, C0062:64, C0062:76, C0063:28, C0063:54, C0063:64, C006B:00, C0082:47, C0082:48, C0082:49, C1B14:01, B10DF:46, U0001:88, U0100:00, U0101:00, U0140:00, U0151:00, U0155:00, U0401:00, U0402:00, U0422:00, U0428:62, U0428:64, U0452:86, U2007:46, U2100:00, U2101:00, U3003:16, U3003:17

• For details on DTCs, refer to [Brake On-board Diagnostic System]. (See ON-BOARD DIAGNOSTIC SYSTEM [DYNAMIC STABILITY CONTROL (DSC)].)

i-stop warning light (amber) illumination condition

― Any one of the following conditions is met:

• Ignition switched ON (check of i-stop control system)

• i-stop OFF switch is on

• Engine stalls due to driver's operation while engine is stopped by i-stop control^*

• Communication error between the instrument cluster and PCM

* :When an engine failure is carried out by a driver's operation, a message is displayed on a multi information display. Please refer to a [Multi Information Display] for the contents of the message. (See MULTI-INFORMATION DISPLAY.)

• The PCM sends an i-stop warning light (amber) flashing/illumination request to the instrument cluster via CAN communication.